Daisy Powerline 990 Repair Manual

Advertising

HOW TO OPERATE

May 26, 2017 a video on how to disassemble and repair a daisy powerline 990 dual power bb gun, requires two 006-70 and two 16-90 orings here is a link to a rebuild kit h. Vintage DAISY Powerline Model No. 990 Pump Co2 BB Gun Rifle Parts or Repair. Time left 5d left. 2 bids +$33.60 shipping. Watch; Vintage Daisy Power Line 990 Dual Power Pump CO2 Rifle WORKS. 9 product ratings - Daisy Powerline 990 922 822 880 Foam Pump Oil Wiper Oiler Part Gun BB Air Rifle. Filling the BB magazine for the PowerLine® 880, 880S, 1880: The loading door is located on the left side of receiver (See. Push door down and fill magazine with approximately 50 BBs. Do not overfill or the feed system may not operate properly. LOAD (PowerLine ® 880, 880S, 1880) LOADING BBs: With the bolt handle back.

CAUTION:

Be sure gun is always pointed in a safe

direction

Step 1. OPEN BOLT
Step 2. PUT “ON” TRIGGER SAFETY
Step 3. PUMP
Step 4. LOAD
Step 5. CLOSE BOLT
Step 6. AIM AT SAFE TARGET
Step 7. TAKE “OFF” TRIGGER SAFETY
Step 8. FIRE
Step 1. OPEN BOLT

Pull straight back on bolt handle, pulling it fully to the rear

(See Drawing No. 1A). The gun cannot fire with bolt open.

Step 2. PUT “ON” TRIGGER SAFETY

The bolt must FIRST be opened, then the trigger safety is

pushed from the left to right so that NO red is showing (See
Drawing No. 1B).

CAUTION:

Gun must always be pointed in a safe

direction.

BOLT HANDLE

LOADING PORT

TRIGGER
SAFETY

NO. 1B

TRIGGER SAFETY ON

TRIGGER SAFETY OFF
red showing on opposite side

NO. 1A

Step 3. PUMP

The bolt must be opened to pump gun. For greater safety,

we recommend that the bolt remain open while pumping and
that you close the bolt only when the barrel can be pointed in
a safe direction. With the muzzle pointed in a safe direction,
pump the gun the desired number of times up to 10. More
power means greater chance of serious injury. Never put fin-
ger on trigger until ready to fire the gun. NOTE: Do not pump
your gun more than 10 times. Muzzle energy increases pro-
duced by more than 10 pumps are minor, and increased
pumping will damage your gun.

CAUTION:

Be sure to grasp pump handle firmly as

you close the lever to prevent it from snapping back and
causing possible injury. Also be careful to keep fingers out of
cocking mechanism when closing lever. (See “PINCH
POINTS,” Drawing No. 2).

WARNING:

Do not open the bolt, close the bolt, and

then pull the trigger before pumping. This procedure can result
in a loaded gun and a projectile being expelled from the gun
during pumping. Recock the gun by opening the bolt and put
“on” trigger safety before pumping as in Steps 1 and 2.

PULL LEVER OUTWARD
FOR FULL STROKE
THEN RETURN

PINCH
POINTS

NO. 2

Filling the BB magazine for the PowerLine® 880, 880S, 1880:

Daisy powerline 990 repair manual download

The loading door is located on the left side of receiver (See

Drawing No. 3). Push door down and fill magazine with
approximately 50 BBs. Do not overfill or the feed system may
not operate properly.

Step 4. LOAD (PowerLine

®

880, 880S, 1880)

LOADING BBs: With the bolt handle back and BBs in the

magazine (See “BB MAGAZINE” section), RAISE the muzzle of
the gun 45 degrees to 90 degrees. When raising the muzzle,
be sure the front sight is pointed upward since the gun may
not feed properly if it is on its side (See Drawing No. 4A). A
BB can be seen on the magnetic tip by looking into the load-
ing port (See Drawing No. 4A). If a BB does not feed onto the
magnetic tip when the muzzle is raised, shake the gun slightly.
Push bolt handle fully forward and the BB is in firing position.
Be sure the front sight is pointed upward when raising the
muzzle to insure proper feeding.

CAUTION:

Always view the BB or Pellet when closing

the bolt and loading port.

WARNING:

BBs feed from the magazine by gravity

which requires that the muzzle be raised. NEVER ASSUME
THE MAGAZINE OR CHAMBER IS EMPTY
even if the gun
does not fire a projectile.

LOADING PELLETS: With the bolt back and BBs removed

from the magazine (See “TO EMPTY MAGAZINE,” Page 7),
advance the bolt forward until the magnetic tip is visibly even
with the rear edge of the pellet loading port; lower the muzzle
and load a pellet, solid end forward (See Drawing No. 5). Push
the bolt handle fully forward and the pellet is chambered in
the firing position.

IMPORTANT: Do not allow a pellet to fall into the rear of the

loading port and become jammed in the BB feed hole. If this
occurs, have a qualified gunsmith remove the left receiver and
clear the loading port or return gun to Daisy.

IMPORTANT: Care must be exercised when shooting pel-

lets while the magazine contains BBs. Loading a BB and pel-
let at the same time may result in a jammed or obstructed
barrel.

Daisy Powerline 990 Repair Manual Instructions

RIGHT

WRONG

NO. 3

NO. 4A

LOADING HOLE

LOADING DOOR

PUSH DOOR
DOWN TO OPEN

BB MAGAZINE

NO. 4B

BB

LOADING
PORT

MAGNETIC
TIP

Daisy Powerline 990 Repair Manual

Step 4. LOAD (PowerLine

®

22X, 22SGT, 22S)

LOADING PELLETS: With the bolt back lower the muzzle

and load a pellet, solid end forward (See Drawing No. 5). Push
the bolt handle fully forward and the pellet is chambered in
the firing position.

NO. 5

LOADING PORT

PELLET

(SOLID

END FORWARD)

MAGNETIC
TIP

4

Daisy Powerline 990 Rebuild Kit

5

Advertising

Daisy Powerline 990 Repair Manual Diagram

This manual is related to the following products:

Daisy Powerline 990 Repair Manual Instructions

PowerLine 880S, PowerLine 1880, PowerLine 177X, PowerLine 22X, PowerLine 22S, PowerLine 22SG

Daisy Powerline 990 Bb Gun

Popular Brands

Daisy Powerline 990 Parts Diagram

Popular manuals