Manual For Elit Diopter Sights
'filed' Swedish diopter sights I've got two sets of Elit diopter sights for a Swedish Mauser. One looks like it has been ground or filed on the mounting surface to fit the rear bridge of the rifle, while one is 'pristine', with several ridges on the bottom.
Type K Diopter Sight manual
Translated from French
Swiss Diopters on the firing line
- The Elit sight, which is very common The Faldt rear sight, Saw one once. The GF Diopter rear sight. These were made by the Military armory I won a few. The Hauges rear sight from Norway. The Hellqvist which looks like R2D2 The Halsikte Hooka rear sight which looks alot like the BUSK sight. The Lyman number 48 rear sight.
- Now with the advent of the new Adjustable Front Sight, even the old Type P’s and PIIs will achieve the 1,000 yard ability. The new P11 Diopter series will use the 1911 Clamp-On-Mount and work with the 1889, Kadett, 1896, 96/11, the G11 and the K11 rifles. The new P11 is also a 1,000 yard system.
- Description: Wonderful diopter rear sight with cover for an M96 or M38 Swedish Mauser. Some surface discoloration, but functionally new. More photos available on request to serious inquirers. Please include your private email address in the G-A message.
Front Cover
ContentsPage |
Description; The type K diopter plus front sight is a aiming system that can be mounted on any K31 without any modification to the weapon. |
Mounting the front sight; -back off the mounting bolt (27) until the threads are no longer visible. -with arrow (26) pointing towards target, slide the front sight assy. over the rifle's fixed sight until it seats -firmly press down on the front sight barrel while while tightening the set screw (29). - check for play in all directions (there should be none). |
Mounting the diopter (rear sight); |
Adjusting the line of sight; |
Aiming process: Align the front tunnel and rear tunnel to give a concentric sight picture, where the target appears just above the front sight post. |
(Pages 12-13) |
|
To see the original click here
Acknowledgements: Thanks to Vaudois for the translation, and thanks to Carlos for the scans.
To return to the Schmidt-Rubin Aftermarket Sight page click here
Sight Options for Schmidt-Rubin Rifles
A number of options exist for those who which to supplement or replace the existing sights on their Schmidt-Rubin Rifles. Some are available commercially, others are homemade. |
The EAW Quick Loc Scope Mount
The EAW scope mount is a no-drilling mount, for use with the K31.
The mount attaches by clamping itself onto the thumb groove on the right side of the K31's reciever.
The rings are weaver style.
The mount is offset to the right, however, the scope does not interfere with ejecting the brass.
The EAW Quick Loc mount can be purchased from New England Custom Guns, although they have to be ordered from Germany, and will cost somewhere between $250-300 for mount, rail and rings. |
Swiss Diopter Sights
TheK31 still remains popular for target shooting. However, the factory sights aren't very conducive to target shooting. As a result, the Swiss manufactured no-gunsmithing diopter sights for use with the K31. |
Photo courtesy of Bob Lorenz
The front sight simply slides over the factory front sight, and is screwed down. Note: in some cases shimming is required. |
Photo courtesy of Bob Lorenz
The rear sight attaches to the thumb groove, much like the EAW Sight.
Photo courtesy of Jim Pregga
The front sight uses replaceable inserts. The inserts can be of the post or peep variety. The rear sight has an adjustable aperture. Diopter sights are extremely difficult to come by in the states. They can be ordered from gunstores in Switzerland, but are quite expensive. Expect to pay at least $225 plus shipping. For a translated manual click here. |
Experimental Swiss Sights
Around 1953 the Swiss began experimenting with electronic sights.
Manual For Elit Diopter Sights Replacement
Picture courtesy of Gregory Smith
The sight replaced the rear sight. The large box to the side is a battery to provide for low light usage. The tests proved unsuccessful, and the scope only saw limited production. |
Other Solutions
As the Swiss solutions are rare and expensive, many individuals have come up with their own means of mounting scope. Note: most of the methods shown below permanently alter the rifle. SwissRifles.com neither condones nor condemns these alterations. |
Adding target sights is a fairly common practice.
Photo courtesy of Roy Headrick
Above is a Williams Foolproof rear aperture sight, #FP-SW, made for the 1911. Note: some wood had to be removed to fit the sight |
Photo courtesy of Roy Headrick
Here a Lyman 17AML front sight replaces the 1911 front sight.
Photo courtesy of Bob Lorenz
Here we have a Tompkins Target sight replacing the front sight of a 1896/11
Photo courtesy of Bob Lorenz
A Redfield Olympic Sight is mounted on the rear.
Photo courtesy of Bob Lorenz
Detail of the modifications to the receiver.
Of course the modifications aren't limited to iron sights.
Picture courtesy of Pierre St. Marie
In the picture above, a dovetail groove has been cut into the left side of the K31s receiver. The mount is then slide into the groove and bolted into place. |
Photo courtesy of Chris Selfslag
Air Rifle Diopter Sights
Above is a homemade attempt a creating a scopemount. Notice the mount replaces the rear sight. |
Photos courtesy of Chris Selfslag
Manual For Elit Diopter Sights Red Dot
Above are some more detailed photos of the mount.
Photo courtesy of Franz Schmidt
Here is another homemade mount, which replaces the rear sight. Note: this rifle mounts the scope forward of the receiver, 'Scout' style. |
Manual For Elit Diopter Sights Picatinny
Be sure to check back from time to time. As more folks send my pictures of their sights, I'll post them |
Return to the Schmidt-Rubin Page